15. i.MX7 Video Capture Driver

15.1. Introduction

The i.MX7 contrary to the i.MX5/6 family does not contain an Image Processing Unit (IPU); because of that the capabilities to perform operations or manipulation of the capture frames are less feature rich.

For image capture the i.MX7 has three units: - CMOS Sensor Interface (CSI) - Video Multiplexer - MIPI CSI-2 Receiver

MIPI Camera Input ---> MIPI CSI-2 --- > |\
                                        | \
                                        |  \
                                        | M |
                                        | U | ------>  CSI ---> Capture
                                        | X |
                                        |  /
Parallel Camera Input ----------------> | /
                                        |/

For additional information, please refer to the latest versions of the i.MX7 reference manual [1].

15.2. Entities

15.3. imx7-mipi-csi2

This is the MIPI CSI-2 receiver entity. It has one sink pad to receive the pixel data from MIPI CSI-2 camera sensor. It has one source pad, corresponding to the virtual channel 0. This module is compliant to previous version of Samsung D-phy, and supports two D-PHY Rx Data lanes.

15.4. csi-mux

This is the video multiplexer. It has two sink pads to select from either camera sensor with a parallel interface or from MIPI CSI-2 virtual channel 0. It has a single source pad that routes to the CSI.

15.5. csi

The CSI enables the chip to connect directly to external CMOS image sensor. CSI can interface directly with Parallel and MIPI CSI-2 buses. It has 256 x 64 FIFO to store received image pixel data and embedded DMA controllers to transfer data from the FIFO through AHB bus.

This entity has one sink pad that receives from the csi-mux entity and a single source pad that routes video frames directly to memory buffers. This pad is routed to a capture device node.

15.6. Usage Notes

To aid in configuration and for backward compatibility with V4L2 applications that access controls only from video device nodes, the capture device interfaces inherit controls from the active entities in the current pipeline, so controls can be accessed either directly from the subdev or from the active capture device interface. For example, the sensor controls are available either from the sensor subdevs or from the active capture device.

15.7. Warp7 with OV2680

On this platform an OV2680 MIPI CSI-2 module is connected to the internal MIPI CSI-2 receiver. The following example configures a video capture pipeline with an output of 800x600, and BGGR 10 bit bayer format:

# Setup links
media-ctl -l "'ov2680 1-0036':0 -> 'imx7-mipi-csis.0':0[1]"
media-ctl -l "'imx7-mipi-csis.0':1 -> 'csi-mux':1[1]"
media-ctl -l "'csi-mux':2 -> 'csi':0[1]"
media-ctl -l "'csi':1 -> 'csi capture':0[1]"

# Configure pads for pipeline
media-ctl -V "'ov2680 1-0036':0 [fmt:SBGGR10_1X10/800x600 field:none]"
media-ctl -V "'csi-mux':1 [fmt:SBGGR10_1X10/800x600 field:none]"
media-ctl -V "'csi-mux':2 [fmt:SBGGR10_1X10/800x600 field:none]"
media-ctl -V "'imx7-mipi-csis.0':0 [fmt:SBGGR10_1X10/800x600 field:none]"
media-ctl -V "'csi':0 [fmt:SBGGR10_1X10/800x600 field:none]"

After this streaming can start. The v4l2-ctl tool can be used to select any of the resolutions supported by the sensor.

# media-ctl -p
Media controller API version 5.2.0

Media device information
------------------------
driver          imx7-csi
model           imx-media
serial
bus info
hw revision     0x0
driver version  5.2.0

Device topology
- entity 1: csi (2 pads, 2 links)
            type V4L2 subdev subtype Unknown flags 0
            device node name /dev/v4l-subdev0
        pad0: Sink
                [fmt:SBGGR10_1X10/800x600 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range]
                <- "csi-mux":2 [ENABLED]
        pad1: Source
                [fmt:SBGGR10_1X10/800x600 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range]
                -> "csi capture":0 [ENABLED]

- entity 4: csi capture (1 pad, 1 link)
            type Node subtype V4L flags 0
            device node name /dev/video0
        pad0: Sink
                <- "csi":1 [ENABLED]

- entity 10: csi-mux (3 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev1
        pad0: Sink
                [fmt:Y8_1X8/1x1 field:none]
        pad1: Sink
               [fmt:SBGGR10_1X10/800x600 field:none]
                <- "imx7-mipi-csis.0":1 [ENABLED]
        pad2: Source
                [fmt:SBGGR10_1X10/800x600 field:none]
                -> "csi":0 [ENABLED]

- entity 14: imx7-mipi-csis.0 (2 pads, 2 links)
             type V4L2 subdev subtype Unknown flags 0
             device node name /dev/v4l-subdev2
        pad0: Sink
                [fmt:SBGGR10_1X10/800x600 field:none]
                <- "ov2680 1-0036":0 [ENABLED]
        pad1: Source
                [fmt:SBGGR10_1X10/800x600 field:none]
                -> "csi-mux":1 [ENABLED]

- entity 17: ov2680 1-0036 (1 pad, 1 link)
             type V4L2 subdev subtype Sensor flags 0
             device node name /dev/v4l-subdev3
        pad0: Source
                [fmt:SBGGR10_1X10/800x600@1/30 field:none colorspace:srgb]
                -> "imx7-mipi-csis.0":0 [ENABLED]