Netconsole

started by Ingo Molnar <mingo@redhat.com>, 2001.09.17

2.6 port and netpoll api by Matt Mackall <mpm@selenic.com>, Sep 9 2003

IPv6 support by Cong Wang <xiyou.wangcong@gmail.com>, Jan 1 2013

Extended console support by Tejun Heo <tj@kernel.org>, May 1 2015

Release prepend support by Breno Leitao <leitao@debian.org>, Jul 7 2023

Userdata append support by Matthew Wood <thepacketgeek@gmail.com>, Jan 22 2024

Please send bug reports to Matt Mackall <mpm@selenic.com> Satyam Sharma <satyam.sharma@gmail.com>, and Cong Wang <xiyou.wangcong@gmail.com>

Introduction:

This module logs kernel printk messages over UDP allowing debugging of problem where disk logging fails and serial consoles are impractical.

It can be used either built-in or as a module. As a built-in, netconsole initializes immediately after NIC cards and will bring up the specified interface as soon as possible. While this doesn’t allow capture of early kernel panics, it does capture most of the boot process.

Sender and receiver configuration:

It takes a string configuration parameter “netconsole” in the following format:

netconsole=[+][r][src-port]@[src-ip]/[<dev>],[tgt-port]@<tgt-ip>/[tgt-macaddr]

  where
       +             if present, enable extended console support
       r             if present, prepend kernel version (release) to the message
       src-port      source for UDP packets (defaults to 6665)
       src-ip        source IP to use (interface address)
       dev           network interface (eth0)
       tgt-port      port for logging agent (6666)
       tgt-ip        IP address for logging agent
       tgt-macaddr   ethernet MAC address for logging agent (broadcast)

Examples:

linux netconsole=4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc

or:

insmod netconsole netconsole=@/,@10.0.0.2/

or using IPv6:

insmod netconsole netconsole=@/,@fd00:1:2:3::1/

It also supports logging to multiple remote agents by specifying parameters for the multiple agents separated by semicolons and the complete string enclosed in “quotes”, thusly:

modprobe netconsole netconsole="@/,@10.0.0.2/;@/eth1,6892@10.0.0.3/"

Built-in netconsole starts immediately after the TCP stack is initialized and attempts to bring up the supplied dev at the supplied address.

The remote host has several options to receive the kernel messages, for example:

  1. syslogd

  2. netcat

    On distributions using a BSD-based netcat version (e.g. Fedora, openSUSE and Ubuntu) the listening port must be specified without the -p switch:

        nc -u -l -p <port>' / 'nc -u -l <port>
    
    or::
    
        netcat -u -l -p <port>' / 'netcat -u -l <port>
    
  3. socat

socat udp-recv:<port> -

Dynamic reconfiguration:

Dynamic reconfigurability is a useful addition to netconsole that enables remote logging targets to be dynamically added, removed, or have their parameters reconfigured at runtime from a configfs-based userspace interface.

To include this feature, select CONFIG_NETCONSOLE_DYNAMIC when building the netconsole module (or kernel, if netconsole is built-in).

Some examples follow (where configfs is mounted at the /sys/kernel/config mountpoint).

To add a remote logging target (target names can be arbitrary):

cd /sys/kernel/config/netconsole/
mkdir target1

Note that newly created targets have default parameter values (as mentioned above) and are disabled by default -- they must first be enabled by writing “1” to the “enabled” attribute (usually after setting parameters accordingly) as described below.

To remove a target:

rmdir /sys/kernel/config/netconsole/othertarget/

The interface exposes these parameters of a netconsole target to userspace:

enabled

Is this target currently enabled?

(read-write)

extended

Extended mode enabled

(read-write)

release

Prepend kernel release to message

(read-write)

dev_name

Local network interface name

(read-write)

local_port

Source UDP port to use

(read-write)

remote_port

Remote agent’s UDP port

(read-write)

local_ip

Source IP address to use

(read-write)

remote_ip

Remote agent’s IP address

(read-write)

local_mac

Local interface’s MAC address

(read-only)

remote_mac

Remote agent’s MAC address

(read-write)

The “enabled” attribute is also used to control whether the parameters of a target can be updated or not -- you can modify the parameters of only disabled targets (i.e. if “enabled” is 0).

To update a target’s parameters:

cat enabled                            # check if enabled is 1
echo 0 > enabled                       # disable the target (if required)
echo eth2 > dev_name                   # set local interface
echo 10.0.0.4 > remote_ip              # update some parameter
echo cb:a9:87:65:43:21 > remote_mac    # update more parameters
echo 1 > enabled                       # enable target again

You can also update the local interface dynamically. This is especially useful if you want to use interfaces that have newly come up (and may not have existed when netconsole was loaded / initialized).

Netconsole targets defined at boot time (or module load time) with the netconsole= param are assigned the name cmdline<index>. For example, the first target in the parameter is named cmdline0. You can control and modify these targets by creating configfs directories with the matching name.

Let’s suppose you have two netconsole targets defined at boot time:

netconsole=4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc;4444@10.0.0.1/eth1,9353@10.0.0.3/12:34:56:78:9a:bc

You can modify these targets in runtime by creating the following targets:

mkdir cmdline0
cat cmdline0/remote_ip
10.0.0.2

mkdir cmdline1
cat cmdline1/remote_ip
10.0.0.3

Append User Data

Custom user data can be appended to the end of messages with netconsole dynamic configuration enabled. User data entries can be modified without changing the “enabled” attribute of a target.

Directories (keys) under userdata are limited to 53 character length, and data in userdata/<key>/value are limited to 200 bytes:

cd /sys/kernel/config/netconsole && mkdir cmdline0
cd cmdline0
mkdir userdata/foo
echo bar > userdata/foo/value
mkdir userdata/qux
echo baz > userdata/qux/value

Messages will now include this additional user data:

echo "This is a message" > /dev/kmsg

Sends:

12,607,22085407756,-;This is a message
 foo=bar
 qux=baz

Preview the userdata that will be appended with:

cd /sys/kernel/config/netconsole/cmdline0/userdata
for f in `ls userdata`; do echo $f=$(cat userdata/$f/value); done

If a userdata entry is created but no data is written to the value file, the entry will be omitted from netconsole messages:

cd /sys/kernel/config/netconsole && mkdir cmdline0
cd cmdline0
mkdir userdata/foo
echo bar > userdata/foo/value
mkdir userdata/qux

The qux key is omitted since it has no value:

echo "This is a message" > /dev/kmsg
12,607,22085407756,-;This is a message
 foo=bar

Delete userdata entries with rmdir:

rmdir /sys/kernel/config/netconsole/cmdline0/userdata/qux

Warning

When writing strings to user data values, input is broken up per line in configfs store calls and this can cause confusing behavior:

mkdir userdata/testing
printf "val1\nval2" > userdata/testing/value
# userdata store value is called twice, first with "val1\n" then "val2"
# so "val2" is stored, being the last value stored
cat userdata/testing/value
val2

It is recommended to not write user data values with newlines.

Extended console:

If ‘+’ is prefixed to the configuration line or “extended” config file is set to 1, extended console support is enabled. An example boot param follows:

linux netconsole=+4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc

Log messages are transmitted with extended metadata header in the following format which is the same as /dev/kmsg:

<level>,<sequnum>,<timestamp>,<contflag>;<message text>

If ‘r’ (release) feature is enabled, the kernel release version is prepended to the start of the message. Example:

6.4.0,6,444,501151268,-;netconsole: network logging started

Non printable characters in <message text> are escaped using “xff” notation. If the message contains optional dictionary, verbatim newline is used as the delimiter.

If a message doesn’t fit in certain number of bytes (currently 1000), the message is split into multiple fragments by netconsole. These fragments are transmitted with “ncfrag” header field added:

ncfrag=<byte-offset>/<total-bytes>

For example, assuming a lot smaller chunk size, a message “the first chunk, the 2nd chunk.” may be split as follows:

6,416,1758426,-,ncfrag=0/31;the first chunk,
6,416,1758426,-,ncfrag=16/31; the 2nd chunk.

Miscellaneous notes:

Warning

the default target ethernet setting uses the broadcast ethernet address to send packets, which can cause increased load on other systems on the same ethernet segment.

Tip

some LAN switches may be configured to suppress ethernet broadcasts so it is advised to explicitly specify the remote agents’ MAC addresses from the config parameters passed to netconsole.

Tip

to find out the MAC address of, say, 10.0.0.2, you may try using:

ping -c 1 10.0.0.2 ; /sbin/arp -n | grep 10.0.0.2

Tip

in case the remote logging agent is on a separate LAN subnet than the sender, it is suggested to try specifying the MAC address of the default gateway (you may use /sbin/route -n to find it out) as the remote MAC address instead.

Note

the network device (eth1 in the above case) can run any kind of other network traffic, netconsole is not intrusive. Netconsole might cause slight delays in other traffic if the volume of kernel messages is high, but should have no other impact.

Note

if you find that the remote logging agent is not receiving or printing all messages from the sender, it is likely that you have set the “console_loglevel” parameter (on the sender) to only send high priority messages to the console. You can change this at runtime using:

dmesg -n 8

or by specifying “debug” on the kernel command line at boot, to send all kernel messages to the console. A specific value for this parameter can also be set using the “loglevel” kernel boot option. See the dmesg(8) man page and The kernel’s command-line parameters for details.

Netconsole was designed to be as instantaneous as possible, to enable the logging of even the most critical kernel bugs. It works from IRQ contexts as well, and does not enable interrupts while sending packets. Due to these unique needs, configuration cannot be more automatic, and some fundamental limitations will remain: only IP networks, UDP packets and ethernet devices are supported.